Fair. No arduino kits though?
Fair. No arduino kits though?
If you’re going to the expense of putting a camera on it, why not take it a little further and slap together an arduino-based sensor suite with some logging? See if you can find any correlations in temp/humidity/gas conc that might help with diagnosis.
If I was capable of getting pregnant, ensuring that I couldnt be forced into a lifelong parenthood based on a single mistake that i may not even consent to would be a much scarier thought than more people speaking a different language.
1.2l water
240ml sodium sulfate
60ml sodium chloride
20ml xantham gum(optional for increased efficacy by keeping the solution homogenous)
Boil water, stir until fully dissolved, a small amount of solute should remain, if not, increase sodium sulfate concentration slowly until it does, indicating no free water molecules available for dissolution.
Solution should now be cooled to below 18c( freezing point) for an end product that will regulate temperature to 18c so long as it have sufficient(negative) thermal energy.
Solution of pure sodium chloride will have freezing point approx -20C, while solution of pure sodium sulfate has freezing point +35C. Adjusting the ratio of NaCl to Na2SO4 will shift the freezing point towards either end of thag spectrum, depending on what phase change temperature you are targetting.
Boot into your bios and check the sata mode. A number of machines that I work with(acer predators most notoriously) will for no discernable reason switch from achi mode to rst optane, resulting in no drive being accessible to the os. Switching back to ahci resolves it.
From a read of that article, it appears that they are feeding it analog inputs, which would imply that it is producing analog outputs. I don’t know if there is a way to evaluate floating point operations on an analog system. That said, my knowledge is very cursory, and someone will surely correct me.
This is actually how I do things when working on remote machines. I have far too many monitors, so dedicating on of them to a handful of btop/nvtop terminals works pretty well.
I admit that it’s a less than perfect setup though, and a single program which could handle the remote connections internally and display an aggregate would be nice.
I’ve never encountered that theory before. As far as my exposure has been, most opposition to 1080 is based around bykill; the effect of the poison on non-target species.
The scientific evidence suggests that the number of natives killed unintentionally by 1080 drops is more than compensated by the increased survival rates of those who now suffer less predation, but walk into any pub and you’ll find half a dozen people throwing out anecdotes about silent forests in the days after 1080 drops.
Swappable batteries resolve this issue pretty well. The energy density is far from comparable, but if you’re already hauling a van or trailer to the job site, then a dozen spare batteries isn’t an issue.
It is a very popular Single Board Computer, with a lot of community support that allows people to build and program a variety of things for a low price. Think of it like lego, but for things which can be useful as well as fun.
Want to run a weather station? Pi and a couple of off the shelf sensors, done.
Want to control your lights or appliances from your phone without getting out of bed? Pi and a couple of off the shelf relays, done.
Want to build a retro gaming console? Pi, a couple of off the shelf controllers and some pre-made emulators, done.
Are you sure you’re not confusing this with the concept of “binning”, which is a pretty standard practice for chips?
You manufacture to a single spec, expecting there to be defects, then you identify the defective units, group them by their maximum usability and sell the “defective” units as lower end chips. IE, everything with 24-31 functional cores gets the “extra” cores disabled and shipped as a 24 core, everything with 16-23 functional cores gets shipped as a 16 core, etc
I would argue that the modern smartphone is different, but by no means better. Between the locked down operating systems and the lack of a physical keyboard they are great for consuming media through approved channels, but basically useless if you want to get any work done with them.
People are still using windows?
Haha, ditto. I’ve got the 34inch 4:3 for tasks like cad and image stuff, then next to it the 34inch ultramodern which I use for spreadsheets or multi-pane stuff, then my extra monitor up that lives up at a weird angle is my at-a-glance home for slack, btop, nvtop and any running scripts I want to keep an eye on.
smartmontools has some good functionality for interfacing with SMART via usb bridges that do not provide native functionality.